Clairemont dings and body-line dents, worked back without breaking the paint, complete satisfaction guaranteed.
The same craft we bring to Clairemont Mesa. Tap WATCH and the page becomes the theater, sound on.
Drag or use the arrows · tap watch for full screen
Mobile paintless dent repair in Clairemont Mesa is not a discount version of shop work. It is the same craft, brought to your driveway when the repair allows for it. The tools, the lighting, and the experience all show up at your door. What does not show up is a lower standard.
That is the value. The factory finish stays. Nothing lands on the Carfax. The car keeps its resale, and most repairs are done the same day. When a repair needs a controlled environment, it routes to our Escondido shop. The decision stays yours.
Parking-lot dings and small body dents, massaged out clean.
See moreBody-line creases brought back along the whole length, no repaint.
See moreDeep panel damage worked back in stages, factory paint kept.
See moreMulti-panel hail, priced by the storm rather than the dent.
See moreDents and door dings on any electric car.
See moreMost dents in Clairemont Mesa land between $197 and $500. A standard door ding runs $197 to $250, a medium dent $275 to $500, and a body-line crease $225 to $600 or more. Large or complex damage starts at $500, and hail is priced by the storm from $1,500. Nothing here is a teaser rate. It is what the work costs.
The panel matters more than most people expect. The same size dent prices differently on a door than on a quarter panel, because access behind the metal is part of the job. Here is the honest breakdown, panel by panel.
| Panel | Price Range | Time | What Sets the Price |
|---|---|---|---|
| Door | $197 to $500 | 60 minutes to 2 hours | The most common panel we repair, because it is the one shopping carts and other car doors reach. Most doors have working access behind the skin, which is why a door ding stays at the bottom of the range.A ding on a door body line runs higher than the same size ding in the flat middle of the panel. |
| Hood | $250 to $900 | 90 minutes to 4 hours | Large, flat, and the most reflective panel on the car, so a hood hides nothing. Hoods are also aluminum on a growing number of vehicles, and aluminum takes far more force and accuracy to move.Underhood bracing decides a lot of the price. Some hoods open up to clean access, others have insulation and structure in the way. |
| Fender | $225 to $700 | 90 minutes to 3 hours | Fenders curve hard and sit right next to a body line, so the metal is under more tension than a flat door. Access often means removing the liner or the light.Fender edges near the wheel arch are the hardest area on the panel and price accordingly. |
| Quarter Panel | $275 to $1,200 | 2 to 5 hours | A quarter panel is welded to the car, not bolted on, so a body shop cannot unbolt and replace it. That is exactly why PDR is worth the most here. Access usually means going in through the trunk or removing interior trim.This is the panel where a body shop quote and a PDR quote differ the most. |
| Roof | $300 to $1,500 | 2 to 6 hours | Reached from inside, through the headliner area, so part of the labor is careful access rather than the dent itself. Roof damage is usually hail or something that fell.Roofs with sunroofs, sensors, or fixed glass narrow the working access and raise the number. |
| Trunk or Tailgate | $250 to $900 | 90 minutes to 4 hours | Horizontal like a hood, so it collects hail and falling objects. Trunk lids often have bracing directly behind the impact area, which changes the approach.Tailgates on trucks and SUVs are usually easier access than a car trunk lid. |
| Bumper | $250 to $750 | 2 to 4 hours | A bumper is plastic, not metal, so it is a different repair entirely. Plastic has memory and can often be reshaped, but scuffs and scrapes through the paint need refinishing to the factory color code.A corner scuff starts around $250. A full scuff panel runs $395, a deeper scratch $550, and an oversized or two-tone bumper up to $750. |
| Scratch, Any Panel | $250 to $750 | 2 to 4 hours | Priced by depth, not by length. A scratch you cannot catch a fingernail in usually polishes out. One that catches has broken the clear coat and needs to be leveled and refinished to your factory paint code.The fingernail test is the honest first answer, and it costs you nothing to do it yourself before sending photos. |
Send two photos and skip the guessing. Straight-on and at a 45-degree angle so the light rakes across the panel. A technician replies with your actual range, usually within minutes. Text 858-408-6200 or read the full pricing breakdown.
Clairemont dings and body-line dents, worked back without breaking the paint, complete satisfaction guaranteed. Clairemont Mesa runs along Clairemont Mesa Boulevard and Balboa Avenue, older shopping centers with lots striped when cars were narrower. Add the 52 and the 805 for commuting and you get a mix of parking-lot dings and freeway rock damage. Doors from the older narrow stalls, hoods from the freeways.
Panel material decides the repair more than the badge does. Aluminum has no memory, so it gives nothing back and every correction takes more force and more accuracy than the same dent in steel. That is not only a Tesla and Rivian story any more. Ford has built the F-150 body in aluminum since 2015, and Toyota, BMW, Mercedes-Benz, and others use it on hoods and tailgates across their ranges.
Aluminum and high-strength steel. Repair quality shows up fast on a dark German paint job.
The highest-volume vehicles on the road here. Newer models use aluminum on hoods and tailgates.
Steel panels, predictable behavior, and usually a same-visit repair.
Common enough now that we work on them weekly. Aluminum, with tight access behind the panels.
Not on the list? We repair every make and model, including trucks, vans, and classics. See EV and Tesla dent repair, aluminum dent repair, or motorcycle gas tank repair.
Clairemont Mesa runs along Clairemont Mesa Boulevard and Balboa Avenue, older shopping centers with lots striped when cars were narrower. Add the 52 and the 805 for commuting and you get a mix of parking-lot dings and freeway rock damage.
Panels we see most in Clairemont Mesa: Doors from the older narrow stalls, hoods from the freeways.
A door strike, almost every time. Another car door swings into your panel at low speed and leaves a round, shallow dent, usually on a door or a rear quarter, usually between knee and waist height.
Here is the part that surprises people. A door strike is not priced by how wide it is. It is priced by how sharp it is. A soft, round ding the size of a golf ball is the most routine repair in the trade and runs $197 to $250. A small, tight impact from a door edge or a corner is a different job, because the metal is bent sharply over a tiny area and the paint is stretched tight across it. Bringing that back without cracking the factory clear coat takes more skill than smoothing a large soft dent, and it runs $250 to $400.
Location on the panel matters just as much. A ding in the open middle of a door has metal that moves freely. The same ding sitting on a body line is under tension from both sides, and the line has to run dead straight again when it is finished. That is why two dents of identical size can be quoted differently, and why an honest quote comes from a photo instead of a phone description.
Door strikes are also the damage most often botched, because they look easy. A technician working fast can push the low spot up and leave a ring of high spots around it. In flat daylight it looks fixed. Under garage lighting, or against the painted line in a parking lot, the whole ring lights up. That is when people find out what they paid for.
Mobile or shop for Clairemont Mesa: This is straightforward mobile work. We come to you and most door strikes are finished in 60 to 90 minutes.
Send a straight-on shot and one at 45 degrees. A technician replies with your actual range, not a starting-at number designed to get us in your driveway.
A bumper is plastic and a scratch is a paint repair, so neither one is paintless dent repair. Both are real services we bring to your location in Clairemont Mesa. Mobile bumper repair starts at $250 for a corner scuff, $395 for a full scuff panel, and $550 for a deeper scratch. Panel scratch repair runs $250 to $750 depending on how deep it cuts.
$250 to $750
Scuffs, scrapes, and curb rash sanded, filled where needed, and refinished to your factory paint code. Done in your driveway in most cases.
$250 to $750
Run a fingernail across it first. If it does not catch, it usually polishes out. If it catches, the clear coat is broken and the area gets leveled and refinished.
Real Dent Time repairs from Clairemont Mesa and across Central San Diego. No cuts, no sped-up footage, no color grading. Drag to browse.
Mobile across Clairemont Mesa and all of Central San Diego. In-shop work at 2120 W. Mission Rd #240, Escondido.
Most dents in Clairemont Mesa land between $197 and $500. A standard door ding runs $197 to $250, a medium dent $275 to $500, and a crease $225 to $600 or more. Larger or complex damage starts at $500, and hail is priced by the storm from $1,500. By panel, a door runs $197 to $500, a hood $250 to $900, and a quarter panel $275 to $1,200. The exact number depends on depth, location on the panel, access behind it, and whether the panel is steel or aluminum. Text a photo to 858-408-6200 for a real figure in minutes.
Yes. We bring mobile paintless dent repair to homes and offices throughout Clairemont Mesa, and most everyday dents are finished on site in 60 minutes to 2 hours. Repairs that need controlled lighting or heavy access route to our Escondido shop, and we tell you which one your dent needs before anything is booked.
Most repairs take 60 minutes to 2 hours. A door ding is often under an hour, a crease or body-line dent runs 2 to 3 hours, and large or complex damage takes half a day to a full day. Hail is the exception at one to four days, because there is no way to shortcut hundreds of individual impacts.
Yes, and they are separate services from dent repair because a bumper is plastic and a scratch is a paint repair. Mobile bumper repair starts at $250 for a corner scuff, $395 for a full scuff panel, and $550 for a deeper scratch. Panel scratch repair runs $250 to $750 depending on depth. Both are done at your location in Clairemont Mesa in most cases.
There are real ones and we will name them. PDR needs the factory paint intact, so if the impact cracked or chipped the clear coat, the metal can still be shaped but the paint needs its own plan. Very sharp, very deep damage where the metal has stretched will improve dramatically but may not vanish completely, and an honest technician tells you that before starting. Panels with no working access behind them need parts removed, which adds labor. What PDR does not do is add filler, add paint, or add a line to your vehicle history.
That depends on whether the paint is actually broken. Run a fingernail across it. If it does not catch, the paint is intact and it is a straight paintless repair from $197. If it catches, the clear coat is broken, and the metal can still be shaped but the finish needs refinishing to your factory paint code, which typically adds $250 to $750 depending on the size of the area. We tell you which one you have from the photos, before you commit to anything.
The shop is open Monday to Friday 8:30am to 4pm, with Saturday by appointment. Photo estimates run around the clock. Send a photo any time, day or night, and you get a real range back, usually within minutes during business hours and first thing the next morning otherwise.
Send a few photos any time, day or night. The line is always open and you always get a reply, with a real price range back within minutes during the day. You approve the number before any tool touches the car.
More on the work: paintless dent repair, PDR insurance claims, aluminum panels, all service areas.